Material Safety Data Sheet Section 1. Identification of the substance Product Name: 2-Bromo-5-fluoro-m-xylene Synonyms: 4-Fluoro-2,6-dimethylbromobenzene Section 2. Hazards identification Harmful by inhalation, in contact with skin, and if swallowed. Section 3. Composition/information on ingredients. Ingredient name: 2-Bromo-5-fluoro-m-xylene CAS number: 14659-58-6 Section 4. First aid measures Skin contact: Immediately wash skin with copious amounts of water for at least 15 minutes while removing contaminated clothing and shoes. If irritation persists, seek medical attention. Eye contact: Immediately wash skin with copious amounts of water for at least 15 minutes. Assure adequate flushing of the eyes by separating the eyelids with fingers. If irritation persists, seek medical attention. Inhalation: Remove to fresh air. In severe cases or if symptoms persist, seek medical attention. Ingestion: Wash out mouth with copious amounts of water for at least 15 minutes. Seek medical attention. Section 5. Fire fighting measures In the event of a fire involving this material, alone or in combination with other materials, use dry powder or carbon dioxide extinguishers. Protective clothing and self-contained breathing apparatus should be worn. Section 6. Accidental release measures Personal precautions: Wear suitable personal protective equipment which performs satisfactorily and meets local/state/national standards. Respiratory precaution: Wear approved mask/respirator Hand precaution: Wear suitable gloves/gauntlets Skin protection: Wear suitable protective clothing Eye protection: Wear suitable eye protection Methods for cleaning up: Mix with sand or similar inert absorbent material, sweep up and keep in a tightly closed container for disposal. See section 12. Environmental precautions: Do not allow material to enter drains or water courses. Section 7. Handling and storage Handling: This product should be handled only by, or under the close supervision of, those properly qualified in the handling and use of potentially hazardous chemicals, who should take into account the fire, health and chemical hazard data given on this sheet. Store in closed vessels. Storage: Section 8. Exposure Controls / Personal protection Engineering Controls: Use only in a chemical fume hood. Personal protective equipment: Wear laboratory clothing, chemical-resistant gloves and safety goggles. General hydiene measures: Wash thoroughly after handling. Wash contaminated clothing before reuse. Section 9. Physical and chemical properties Appearance: Not specified Boiling point: No data No data Melting point: Flash point: No data Density: No data Molecular formula: C8H8BrF Molecular weight: 203.1 Section 10. Stability and reactivity Conditions to avoid: Heat, flames and sparks. Materials to avoid: Oxidizing agents. Possible hazardous combustion products: Carbon monoxide, hydrogen fluoride, hydrogen bromide. Section 11. Toxicological information No data. Section 12. Ecological information No data. Section 13. Disposal consideration Arrange disposal as special waste, by licensed disposal company, in consultation with local waste disposal authority, in accordance with national and regional regulations. Section 14. Transportation information Non-harzardous for air and ground transportation. Section 15. Regulatory information No chemicals in this material are subject to the reporting requirements of SARA Title III, Section 302, or have known CAS numbers that exceed the threshold reporting levels established by SARA Title III, Section 313.
formation of organozincreagents and subsequent cross-coupling with aryl halides and activated carboxylic acids is reported. Formation of organozincreagents is achieved by pumping organic halides, in the presence of ZnCl2 and LiCl, through an activated Mg-packed column under flow conditions. This method provides efficient in situ formation of aryl, primary, secondary, and tertiary alkyl organozinc reagents
Robust acenaphthoimidazolylidene palladiumcomplexes have been demonstrated as highlyefficient and general catalysts for the sterically hindered Suzuki–Miyaura cross-coupling reactions in excellent yields even with low catalyst loadings under mild reaction conditions. The high catalytic activity of these complexes highlights that, besides the “flexible steric bulky” concept, σ-donor properties of
[EN] BROMODOMAIN INHIBITORS<br/>[FR] INHIBITEURS DE BROMODOMAINE
申请人:ABBVIE INC
公开号:WO2018068283A1
公开(公告)日:2018-04-19
Provided herein are compounds of formula (I) wherein R 1, Y, L 1, G 1, X 1, X 2, L 2, R 2, R 3, and R 4 have any of the values defined in the specification, and pharmaceutically acceptable salts thereof, which are useful as agents in the treatment of diseases and conditions, including inflammatory diseases, cancer, and AIDS. Also provided are pharmaceutical compositions comprising compounds of formula (I).
Synthesis and Characterization of Acridinium Dyes for Photoredox Catalysis
作者:Alexander White、Leifeng Wang、David Nicewicz
DOI:10.1055/s-0037-1611744
日期:2019.4
platform for synthetic methods development. The prominent use of acridinium salts as a sustainable option for photoredox catalysts has driven the development of more robust and synthetically useful versions based on this scaffold. However, more complicated syntheses, increased cost, and limited commercial availability have hindered the adoption of these catalysts by the greater synthetic community. By
Described are imino-azacycle-benzamide compounds compounds that inhibit WDR5 and associated protein-protein interactions, pharmaceutical compositions including the compounds, and methods of using the compounds and compositions for treating disorders and conditions in a subject.