Material Safety Data Sheet Section 1. Identification of the substance Product Name: 4-Bromo-2’-methylbenzophenone Synonyms: (4-Bromophenyl)(2-methylphenyl)methanone Section 2. Hazards identification Harmful by inhalation, in contact with skin, and if swallowed. Section 3. Composition/information on ingredients. Ingredient name: 4-Bromo-2’-methylbenzophenone CAS number: 27428-59-7 Section 4. First aid measures Skin contact: Immediately wash skin with copious amounts of water for at least 15 minutes while removing contaminated clothing and shoes. If irritation persists, seek medical attention. Eye contact: Immediately wash skin with copious amounts of water for at least 15 minutes. Assure adequate flushing of the eyes by separating the eyelids with fingers. If irritation persists, seek medical attention. Inhalation: Remove to fresh air. In severe cases or if symptoms persist, seek medical attention. Ingestion: Wash out mouth with copious amounts of water for at least 15 minutes. Seek medical attention. Section 5. Fire fighting measures In the event of a fire involving this material, alone or in combination with other materials, use dry powder or carbon dioxide extinguishers. Protective clothing and self-contained breathing apparatus should be worn. Section 6. Accidental release measures Personal precautions: Wear suitable personal protective equipment which performs satisfactorily and meets local/state/national standards. Respiratory precaution: Wear approved mask/respirator Hand precaution: Wear suitable gloves/gauntlets Skin protection: Wear suitable protective clothing Eye protection: Wear suitable eye protection Methods for cleaning up: Mix with sand or similar inert absorbent material, sweep up and keep in a tightly closed container for disposal. See section 12. Environmental precautions: Do not allow material to enter drains or water courses. Section 7. Handling and storage Handling: This product should be handled only by, or under the close supervision of, those properly qualified in the handling and use of potentially hazardous chemicals, who should take into account the fire, health and chemical hazard data given on this sheet. Store in closed vessels. Storage: Section 8. Exposure Controls / Personal protection Engineering Controls: Use only in a chemical fume hood. Personal protective equipment: Wear laboratory clothing, chemical-resistant gloves and safety goggles. General hydiene measures: Wash thoroughly after handling. Wash contaminated clothing before reuse. Section 9. Physical and chemical properties Appearance: Not specified Boiling point: No data No data Melting point: Flash point: No data Density: No data Molecular formula: C14H11BrO Molecular weight: 275.1 Section 10. Stability and reactivity Conditions to avoid: Heat, flames and sparks. Materials to avoid: Oxidizing agents. Possible hazardous combustion products: Carbon monoxide, hydrogen bromide. Section 11. Toxicological information No data. Section 12. Ecological information No data. Section 13. Disposal consideration Arrange disposal as special waste, by licensed disposal company, in consultation with local waste disposal authority, in accordance with national and regional regulations. Section 14. Transportation information Non-harzardous for air and ground transportation. Section 15. Regulatory information No chemicals in this material are subject to the reporting requirements of SARA Title III, Section 302, or have known CAS numbers that exceed the threshold reporting levels established by SARA Title III, Section 313.
Selective Acylation of Aryl- and Heteroarylmagnesium Reagents with Esters in Continuous Flow
作者:Benjamin Heinz、Dimitrije Djukanovic、Maximilian A. Ganiek、Benjamin Martin、Berthold Schenkel、Paul Knochel
DOI:10.1021/acs.orglett.9b04254
日期:2020.1.17
A selectiveacylation of readily accessible organomagnesium reagents with commercially available esters proceeds at convenient temperatures and short residence times in continuous flow. Flow conditions allow us to prevent premature collapse of the hemiacetal intermediates despite noncryogenic conditions, thus furnishing ketones in good yields. Throughout, the coordinating ability of the ester and/or
catalysts with a PNP type ligand, the electron-rich chiral PNP ligands have still been rarely reported because of the difficulties in synthesis and the nature of air-sensitivity. Herein, we report a novel chiral PNP ligand (Heng-PNP) with both a rigid backbone and a bulky tert-butyl group on the phospholane motif. We successfully obtained its divalent iron complex. The chiral environment of its Ir(III) complex
generated hydroxy‐o‐quinodimethanes with high stereoselectivity. We used a chiral organic catalyst, derived from natural cinchona alkaloids, to activate maleimides toward highly stereoselective Diels–Alder reactions. An unconventional mechanism of stereocontrol is operative, wherein the organocatalyst is actively involved in both the photochemical pathway, by leveraging the formation of the reactive photoenol
Forging Fluorine-Containing Quaternary Stereocenters by a Light-Driven Organocatalytic Aldol Desymmetrization Process
作者:Sara Cuadros、Luca Dell'Amico、Paolo Melchiorre
DOI:10.1002/anie.201706763
日期:2017.9.18
2-fluoro-substituted cyclopentane-1,3-diketones (1) leads to the stereoselective construction of valuable fluorine-containing quaternary stereocenters. The chemistry exploits the ability of a readily available amido-thiourea catalyst to selectively activate one of the enantiotopic carbonyl groups within 1 and promote an intermolecular aldol reaction of hydroxy-o-quinodimethanes, which are photochemically
Abstract Disclosed herein is a photochemical organocatalytic strategy for the direct enantioselective Mannich-type reaction of 2-alkylbenzophenones and cyclicimines. The chemistry exploits the light-triggered enolization of 2-alkylbenzophenones to generate transient hydroxy-o-quinodimethanes. These fleeting intermediates can be stereoselectively intercepted by imines upon activation with a chiral organic